What you should know about effervescent forms before formulate and manufacture it? As per revised definition proposed to US FDA, Effervescent tablet is a tablet intended to be dissolved or dispersed in water before administration. Effervescent tablets are uncoated tablets that generally contain acid substances and carbonates or bicarbonates and which react rapidly in the presence of water by releasing carbon dioxide. They are intended to be dissolved or dispersed in water before use. You will find the process of Effervescent Tablet Formulation and Manufacture here.

Many studies have demonstrated that effervescent tablets and powders enhance absorption of a number of active ingredients, such as disulfiram and caffeine. That’s because the carbon dioxide created by the effervescent reaction can induce enhanced active-ingredient permeability due to an alteration of the paracellular pathway. It is theorized that the carbon dioxide alters (widens) the intercellular space between cells, which leads to greater absorption of active ingredients (both hydrophobic and hydrophilic).

Read more about :Vitamin C Effervescent Tablet : Formula, Manufacturing and Consideration of Material and Method of Manufacture Selection
There are several categories of active ingredients: Those that are difficult to digest or disruptive to the stomach, calcium carbonate for example. In a normal tablet or powder, the calcium carbonate dissolves in the stomach acid and is carried into the digestive system for absorption. However, calcium carbonate releases carbon dioxide when it dissolves in the GI, which usually produces gas in the stomach. As people age, they have less acid in the stomach, and thus a calcium carbonate tablet may pass through the stomach without dissolving. That, in turn, may lead to constipation. However, if the calcium carbonate is taken in an effervescent formulation, the calcium dissolves in water, is readily available for the body to absorb, and there is no risk of excessive gas in the stomach or of constipation.

The low pH in the stomach can cause active ingredients to become denatured, lose activity, or cause them to remain inactive, such as Amino acid and vitamins. Effervescent ingredients, however, can buffer the water-active solution so that the stomach pH increases and thus prevent the degradation or inactivation of the active ingredient. This buffering effect induces the stomach to empty quickly, usually within 20 minutes into the small intestine. The result is maximum absorption of the active ingredient.

A typical effervescent tablet (1 inch in diameter weighting 5 grams in total weight) can include more than 2,000 milligrams of water soluble active ingredients in a single dose. If the required dose is larger than that, the sachet (powder form) is a common means of delivery.

Those that are susceptible to light, oxygen, or moisture. Typical effervescent formulations have less than 0.5 percent of free moisture. To maintain that level and prevent other damage from the ambient environment, the formulation’s package should be 0.001-inch-thick aluminum that completely blocks light, oxygen, and moisture.

Effervescence Tablet Formulation
Acid Reaction. Effervescence is the reaction (in water) of acids and bases producing carbon dioxide. Typical acids used in this reaction are citric, malic, tartaric, adipic, and fumaric.
  • Citric acid is the most commonly used. It taste like citrus.
  • Malic acid used in effervescent formulas for a Smoother aftertaste, but the price of malic acid is higher than citric acid.
  • Tartaric, adipic, and fumaric had low water solubilities and used sparingly.

Bases Reaction. Typical bases used in the effervescent reaction are sodium bicarbonate, potassium bicarbonate, sodium carbonate, and potassium carbonate. Sodium bicarbonate is very common in effervescent formulas and produces a clear solution after tablet disintegration. When sodium levels are a concern, potassium bicarbonate is used. Both types of carbonates are used mainly as desiccants.

Binders. Binders in effervescent tablets use to bring the tablet hardness to a point where handling is possible. These binders should be water-soluble and include dextrose, sorbitol, xyitol, and lactose. Be careful, binders can carry free moisture into the tablet, which is undesirable and can increase disintegration times when used in large quantities. The ideal amount of binder is one that makes the tablet hard enough to handle, but soft enough to disintegrate and dry enough to be stable.

Sweeteners and Flavors. Depending on the product, formulators can use color (artificial or natural), sweeteners (acesulfame potassium, sodium saccharin, aspartame, and surcalose), and flavors (artificial or natural) to enhance a product or to mask off-notes derived from the active ingredients.

Lubricants. Lubrication of effervescent tablets has historically been the main stumbling block to an acceptable, marketable product. Typical lubricants such as magnesium stearate are not useful due to their insolubility in water. Most formulators have to use water-soluble lubricants such as sodium benzoate, polyethylene glycol, and adipic acid. But, There are tablet presses that use lubrication spray on the punches so that the formula does not require lubrication.

Effervescent Tablet Manufacture and Production
Basically, the manufacture of effervescent tablets are identical to used for making conventional tablets and powders, but production must occur in very low humidity areas. Effervescent granulations can be mixed in conventional blending equipment, such as ribbon, twin-cone, drum mixer and V-type blenders. All equipment should be well grounded and absolutely dry after wash-down. Any traces of moisture in the equipment will give erratic granulation results and most likely result in lost batches of product.

Read more about :Vitamin C Effervescent Tablet : Formula, Manufacturing and Consideration of Material and Method of Manufacture Selection

Wet Granulation. Wet granulation of the effervescent base can be performed by carefully adding 0.1 to 1.0 percent water (weight-to-weight basis) to the chosen blending equipment. The granulation steps must be precisely timed and the ingredients mixed thoroughly to distribute the solvent or binder solution evenly in the blend. The mix is then quickly discharged to drying ovens. You must constantly monitor the operational parameters of all equipment, especially drying equipment, as variations in drying times and temperatures can affect the finished product. While stable granulations will ultimately be made, vast differences in tablet hardness and disintegration times can result from over- or under-reacting the granulation.

After drying, the granulation is sized, and a final mix is performed. Fluid-bed dryers have been used for many years to make effervescent granulations. Basically, the water or binder solution is sprayed onto the effervescent mixture while it is suspended in a stream of hot, dry air. The humidity and temperature of the air serve to stop the effervescent reaction quickly and uniformly. To ensure that you produce a free-flowing granulation, chose the particle sizes carefully and monitor all systems closely. Vacuum granulators have also been used to make effervescent granulations. This equipment gives you a very controlled granulation of the product and allows a dustfree environment. The equipment also generally requires less power and less operating space than other types of granulators. In operation, the water or binder solution is sprayed onto the effervescent mixture during blending.

Drying occurs by placing the granulation under vacuum and heating it via a thermal jacket. Effervescent products normally require tablet presses that can deliver high compression forces. If the tablets are to be wrapped in foil or placed into a tube, give careful attention to the tablet parameters during Compression. Monitor the tablet thickness to ensure the wrapping or packaging equipment can handle the tablets. Strict control of temperature and humidity in all areas is a must (65 to 75ºF, relative humidity of 10 percent), or the formulation will begin a chemical reaction after it’s packaged. In essence, the tablet will self-destruct because the byproducts of an effervescent reaction are water and carbondioxide.

The best way to stabilize an effervescent product is to produce it in an environment where humidity is under strict control and to package it in a suitable moisture barrier. All ingredients in the formulation must be anhydrous. Your contractor should test for free moisture before packaging.

Packaging Materials of Effervescent Tablet
Many effervescent product failures occur each year due to inadequate packaging materials. Why? Because many pharmaceutical industries purchase those materials based on pricing, rather than its stability. The most common types of packaging are foil packets and tubes. Pinholes are a common problem in foil packets. By going to a heavier-gauge foil (usually more expensive), you will greatly reduce the number of pinholes.

The area within the packet should be large enough to hold the tablets without creating stress on the foil and as small as possible to minimize the amount of “room-air” that it can trap inside with the tablets. Given the very low humidity of effervescent tabletting operations, the tablets are so dry that a relative humidity of even 10 percent is fairly high when it’s trapped in close contract with tablets. Tubes are made of plastic, glass, or extruded aluminum with fitted caps containing desiccants. Desiccants are used to “bind-up” any free moisture in the tablet or in the air to prevent the effervescent reaction from starting prematurely. Be sure to conduct well-performed stability studies on tubes and any other packaging you are considering. Figure 2 shows a packaging machine wrapping effervescent tablets.

Stability Testing of Effervescent Tablet.
After packaging, effervescent products should be placed in a test chamber set at 40ºC and 75 percent relative humidity for at least 3 months to determine whether they will be stable. At the end of the third month, you should perform physical tests (package leak test, tablet appearance, disintegration time, tablet hardness, and sensory evaluation of the product) to determine whether any off-notes developed during testing. You should also perform chemical assays (HPLC/MS) to test the actives in the tablet. Has there been any product degradation? If so, why?

The common reasons for degradation of an effervescent product are :
  • The packaging material does not have a moisture vapor transmission rate of 0. Moisture vapor can enter the package.
  • The seal of the foil pouch is compromised. This can happen when there is too much dust in the packaging area or when a machine malfunctions during wrapping of the product.
  • There are ingredients in the formula that are not compatible with each other or with the effervescent components chosen for the product. Here, the pharmaceutical or nutraceutical company should ensure that its R&D department collaborates closely with the contract manufacturer. Each staff member must learn which raw materials are suitable for a successful effervescent product and which are not.
Read more about :Vitamin C Effervescent Tablet : Formula, Manufacturing and Consideration of Material and Method of Manufacture Selection

    Search